RAM 4000 Instrukcja Obsługi

(AVM-BA48)Instruction and Operations ManualRefrigerated Vending MachineManufacturer:Automated Vending Technologies, Inc.Recommended Location:This Refr

8 II Working Principle and the StructureThe RAM 4000 Vending Machine from AVT, Inc. comes standard with configurable trays and augers, especially d

9Flow Chart:1 23456789CLEARENTER0Total AmountChange ChangeSTART Return KnobE N DBill insertCoin InsertKEY PAD Change ReturnDelivery BinChange outlet

10(II)StructureDisplay DoorLockDelivery BinBill ValidatorDisplayKey PadCoin InsertReturn KnobChange Retu rn

11 III Operating InstructionIn order to ensure successful daily operation of the RAM 4000 vending machine, the owner should

12(I) ?The trays are tiltable. The tray will tilt down and stop at the limit position.(As shown in the Picture III). ? After loading products, lift t

13(III) INSTALLATION AND INSTRUCTION FOR THE BILL/COIN If not provided by AVT. Please refer to the owners manual for these products.(1)The fi

14Picture lV(2)CONNECTION INSTRUCTIONS:Prepare a validator wire with three terminals (two are the same, the third one is different). For the two term

15(IV) MACHINE START-UP1). Press the RESET button once. This button is located at the bottom right hand corner of the cabinet. 3). Make sure that t

16(V)The Locking and Unlocking of the Door1.Unlock the doorInsert the key, revolve the handle counter clockwise until the screw thread is completely

17The LED display screen has three (3) different functions:1). In Retail. The Green light for retail indicates the machine is in use and able to con

VENDING MACHINEImportant Machine Placement Criteria andWarranty Information ……………………………………………………1Unpacking and Installation Instructions …………………………………

181.Function IntroductionThe operator can control and examine the vending machine by using the attached remote control to set the price, clock

19Step Operations Display Description 1 Press SALE STAT Once. 1. “TL” represents the total amount of the products. 2. “1234560” is the

20(2)CHL SETThere are six lines of trays. The tray's number should be 11-18, 21-28,……61-68.Step Operation Display Description 1 Press CHL S

213 Press SET/START once Cancel the Set. After canceling the set the tray’s number will flicker. 4 Press SET/START twice Saving the Set. Aft

223 Press the keyboard to choose the tray number. 11 Choose No. 11 tray. Note: When the chosen tray No. does not set, the system

2310 Press SET/START The selected coin pipe will begin to return coins until you press the FINISH button. 11 Press FINISH / Exit The R

24(5)Malfunction InquiryNote:1. If the machine is equipped with the Vend Sensing System (VSS), it will automatically detect if the product vended pro

25(6)SET SELLING WITH AWARDStep Operation Display Description 1 Press SALE MODE Once. It is in Force Vending Mode 2 Press UP or DOWN or FC

26(7) PARAMETER SET SYSTEM CLOCKStep Operation Display Description 1 Press MODE/STOP Once. It is in the system clock setting mode. 2 Press SET/STA

278 Press SET/START Now you can set the hour and save the date’s setting. 9 Press UP or DOWN The range of hour is 0-23. 10 Press SET/START Now you

The Security Matters Must Be Read Before InstallationYour safety and the safety of others are very important. We have provided many importa

28ENERGY-SAVINGStep Operation Display Description 1 Press MODE/STOP Twice Now it is in ENERGY-SAVING Mode. 2 Press SET/START The three fig

29LAMP TIMEStep Operation Display Description 1 Press MODE/STOP Three times. Now you can set the ON/OFF Mode of the lamp. 2 Press SET/START

309 Press UP or DOWN The range is 00 59, use one minute as a unit. 10 Press FINISH / Save the settings for the OFF time of minutes an

314 Press FINISH / Save the setting and leave REFRIGERATION TEMP condition. MACHINE NUMBERStep Operation Display Description 1 Press MODE/

323 Press UP or DOWN The range for the first figure is 0-9,A-F. 4 Press SET/START The second figure flickering will allow you to assig

33Step Operation Indicator light Description 1 Press L ROOM once The green LED light on. The refrigeration is ON. 2 Press L ROOM twice The green L

34Malfunction Content List of AVM-BA48( Vending Machine):Malfunction Content Malfunction description GOOD The machine is working well. (There is no m

USB GPRS USB GPRS USB GPRS USB GPRS Optional Parts No Yes No No No No Yes Yes Malfunction DisplayIt will display EA07, however, the

36After opening the door, please note:The machine will turn to remote control locked mode, if there is not any operation within 30 minutes. The

It is necessary to conduct periodic maintenance on your vending machine in order to keep it in the best working condition possible.

21). Check polarity of the outlet you wish to use. It is important that the polarity is checked. If a problem exists with the socket it can cause ser

machine trays function properly.7). Coinage Maintenance Periodic lubrication of the transmission position will reduce friction to ensure flex

When Maintenance is Required on the Refrigeration Unit:If maintenance is required on the refrigeration unit, this can be done by following the steps b

Attachment I Quick Troubleshooting GuideTroubles Reasons Solutions NO POWER 1. The socket doesn’t work. 2. The electrical plug is not in its r

Troubles Reasons Solutions No product is being delivered when inserting money. 1. The money is jammed. 2. The products are sold out. 3. The produ

Attachment II VENDING MACHINE SCHEMATICSBreakdown Drawing for the RAM 4000 Vending MachineREFRIGERATION SYSTEMDOORTRAYCHEST 42

The Breakdown Drawing of Chest Left Slide of the TrayInternal PartsDelivery Port PartsChest SeamFootUpper HingerLeft Side Board Port for Evaporator Ro

Double Paned GlassLockStainless Steel Control UnitsDisplayKey-PadReturn KnobCoin InsertChange OutletDelivery PortStainless Steel Delivery PortThe Br

The Breakdown Drawing of TrayTray Casing Seam AugersAugersSpring DriverElectrical Plug 45

The Breakdown Drawing of the Refrigeration SystemBottom Board of CompressorMotor-CompressorScrew for GroundingVent-PipeWater BoxCondenser FanFan Tres

47

35). Check the fixed metal parts. Especially if there has been an earthquake of a 5.0 or higher or after machine has been moved from one location to

Automated Vending Technologies, Inc.Corporate Office:341 Bonnie Circle, Suite 102 Corona, CA [email protected]

4(I)(1) Remove packaging materials.IMPORTANT: Do not remove any permanent instructions or the data label on your vending machine.Remove tape

5(3) THE FIXATION OF THE BOTTOMMake sure the reliability of the floor surface (The minimum area is 43.5×41.3in.). While positioning, the detailed pro

6Note: a. The installation should be performed by trained technicians. b. The maximum angle of the machine is 15° when installing and in tra

7Sketchmap of Indoor GroundingGroundin g PortGroundin g Socket